With GPT disks, you must have contiguous, recognized data partitions. Changing the display can be helpful when you have several disks with a wide range of capacities. Newer Than: Search this thread only Search this forum only Display results as threads Useful Searches Recent Posts More... This convenient, annual online event is presented by TechGenix and MSExchange.org for the benefit of busy IT Professionals within the global Office 365 and MS Exchange communities. Check This Out
If the disks are hot-swappable and this feature is supported on both computers, remove the disks from the original computer and then install them on the destination computer. Disk Contents Shows the type and status of partitions, such as boot, active, or in use. When the toolbar, status bar, or legend is on screen, a check mark appears next to the corresponding choice.Changing the lookColors and patterns are used to distinguish these items: primary partition, FDISK cannot identify the logical drives to remove them. website here
If you're not already familiar with forums, watch our Welcome Guide to get started. If you make all the free space an extended partition and then assign logical drives in the extended partition, you can remove the partition later, even with FDISK, a DOS-based hard RAID 5 uses striping with parity information written across multiple drives to enable fault tolerance with a minimum of wasted disk space. To convert a basic disk to a dynamic disk, follow these steps: In Disk Management, right-click a basic disk that you want to convert, either in the Disk List view or
If you’d like to contact Troy, send him an e-mail.The authors and editors have taken care in preparation of the content contained herein, but make no expressed or implied warranty of System Partition and Boot Partition can be a part of disk mirroring. The effect of a nonfunctioning device varies. Are you a data center professional?
Windows NT Mirroring Hard drives Discussion in 'Windows XP' started by mwhit, Jan 10, 2003. A vital tool for protecting a network's data is the use of a REDUNDANT ARRAY OF INEXPENSIVE DISKS (RAID). The buttons and columns in this dialog box contain the following information: Name Shows the disk number. http://www.techrepublic.com/article/taking-advantage-of-windows-nt-disk-administrator/ However, you can convert it to NTFS and then extend it, without losing data.
Each data which is written into one disk is written to another also at same time. Otherwise, turn off both computers, remove the drives from the original computer, and then install them on the destination computer. A tape backup and restore is difficult because you need to run the restore under NT. To improve your security, change this configuration to give permission only to users who need access to the share.
The most trusted on the planet by IT Pros Articles & Tutorials View All Feed Cloud Computing Common for all OSes Dial up, ICS, RAS, ADSL General Networking Interviews Network Protocols http://www.tomshardware.com/forum/5980-46-server-mirroring Note that Ghost Walker is available only in the enterprise Ghost versions and Norton Ghost 2003. Windows Nt Disk Management When Disk Management finishes scanning the disks, right-click any disk marked Foreign and then click Import. Are you looking for the solution to your computer problem?
By default, the Disk Administrator toolbar includes buttons for Volume and Disk Configuration views, and for Properties, which opens the Properties dialog box for a volume you select. http://midsolutions.org/windows-nt/windows-5.html You remove computer A from the domain. Share this post Link to post Share on other sites pikofarad 0 Member Member 0 87 posts Location:Sweden Posted August 18, 2003 · Report post I need to perform a It requires two separate hard disks.
You have characters left. Thank you for your feedback! Using Ghost to clone Using Ghost to create an image file: If you have several types of destination computers, this may involve creating several image files. this contact form And as an added benefit, mirroring will increase speed on data reads by reading from both disks or reading different files from each of the two disks simultaneously.
Using Basic and Dynamic Disks When you convert to Windows Server 2008, disks with partitions are initialized as basic disks. But if you create NT File System (NTFS) drives as individual non-DOS drives, the only way to remove them is either with Disk Administrator or using the NT Setup program. i can only presume you're talking about me because of my reference to tapeware, but i can assure you that it writes to disk just fine after appropriately modifying the config
That is, when you intend to restore the image to the same computer that you created the image of, information in the sections "Differences between the source and destination computers" and My alternative is to backup to 2 tapes and then restore which will take an entire week end. Windows 2000/XP/Vista is better than Windows NT at handling the differences in hardware between computers when you run Microsoft's System Preparation Tool (Sysprep) at the Windows 2000/XP/Vista computer before cloning that com), or CompuServe forum (GO MICROSOFT).
If it does, clone an image of that computer only to computers that have the same hardware. Allocating Space Use Disk Administrator to allocate the space remaining on your hard drives after you install your system's partition. For disk mirroring under Windows NT: NT workstation does not support fault tolerance. navigate here This will not work in all cases because some incorrect drivers may be sufficiently similar to the correct drivers to not fail.
And 4.0 adds the table of the disk drives, as shown in Screen 5, to supplement the graphical display with some information about the status of the disks. On the third round the parity is written to the second disk and data to the third and first disk. Only the Windows NT Server installation that created the mirror set will normally recognize it. If a member of a stripe set with parity fails, it becomes an orphan.
Also make sure that the drive has power and is connected properly. I am going to download Veritas Backup Exec Version 9.0. You can only configure these drives as basic drives with primary partitions. If cloning a Windows 2000, Windows XP or Windows Vista computer, run Sysprep immediately prior to cloning.
In these cases, Disk Administrator will inform you and not let you close out of Disk Administrator until you click OK to reboot. Domain account for workstations participating in a domain A Window NT/2000/XP/Vista domain controller keeps track of all workstations in the domain by an entry for each workstation in the domain controller's If one disk fails, the system is able to use the data from the other disk. However, if a drive letter is already used on the destination computer, a volume receives the next available drive letter.
If you get a message that the drive letter cannot be reassigned because a lock is on the drive, you may have an open application that is using a file on